GUIDA ALL'INSTALLAZIONE
18 passaggi per completare un(a) Pergola bioclimatica manuale.
Pergola bioclimatica autoportante in alluminio con manovella manuale — senza motore, senza firmware, tre dimensioni da una procedura unica in 18 passaggi.
-
01
Layout del sistema e linea di riferimento
Set the system datum and mark the four foot-plate centres on the slab.
TELAIO18 min -
02
Posizionare le piastre di base
Place the four PN-FP-500 foot plates and anchor with M10 buldex.
TELAIO25 min -
03
Sollevare i quattro pilastri
Lift each PN-DZ-500 pillar onto its foot plate stud — two installers per pillar.
TELAIO25 min -
04
Installare la grondaia portante posteriore
Install the rear PN-GU-500 carrier gutter — slope 1.5% toward the front.
TELAIO18 min -
05
Installare la grondaia portante anteriore
Install the front PN-GU-500 carrier gutter — match heights within 2 mm.
TELAIO18 min -
06
Installare le grondaie laterali
Install left and right PN-GU-501 side gutters — verify diagonals (3×3: 386 · 3×4: 466 · 3×5: 554.5 cm).
TELAIO25 min -
07
Sigillare i giunti d'angolo
Apply neutral-cure silicone bead at all four upper corner joints.
TELAIO12 min -
08
Installare le guide laterali delle lamelle
Slide PN-LR-500 blade side rails into the frame — pre-set pivot positions.
LAMELLE18 min -
09
Preparare le lamelle
Prepare the louvre blades — fit pivot pins, lay out on a clean covered surface.
LAMELLE18 min -
10
Installare la prima lamella
Install the first blade — verify free rotation and flush closed position.
LAMELLE15 min -
11
Completare il campo lamelle
Complete the blade array — equal pitch using a spacer gauge.
LAMELLE25 min -
12
Collegare la trasmissione manuale
Connect PN-SC-500 manual linkage — all blades must move together.
LAMELLE20 min -
13
Installare la manovella manuale
Install PN-CR-500 crank gear and PN-GT-500 drive shaft — test full cycle.
LAMELLE20 min -
14
Impostare i finecorsa di apertura / chiusura
Set crank end-stops for fully closed and fully open positions.
LAMELLE18 min -
15
Installare i profili di chiusura
Install PN-CP-500 pillar caps and PN-CP-501 gutter closing profiles.
FINITURA15 min -
16
Installare gli scarichi di drenaggio
Connect PN-WT-100/PN-WT-101 drainage tubes inside front pillars and test water flow.
FINITURA18 min -
17
Test funzionale finale
Final functional test — open, close, verify even closure across array.
FINITURA12 min -
18
Pulire e consegnare
Clean powder coating, demonstrate to customer, hand over warranty card.
FINITURA12 min
Informazioni su questa guida all'installazione pergola bioclimatica manuale
Luxa Sereno 500M — Pergola bioclimatica manuale · LuxaShade aluminium roof family. 18 steps · 2 installers · Edition 2026.1.
EN AW-6063 T6 alloy · QUALICOAT class 2 powder coating · EN 1991-1-4 wind-load rated · RTS-compatible motor wiring on motorised variants.
Perché seguire la procedura ufficiale PONARC × LuxaShade
- EN 1991-1-4 · QUALICOAT class 2 · EN AW-6063 T6
- RTS-compatible motor wiring (motorised variants)
- Gutter slope 1.5% · drainage inside columns
- Edition 2026.1 · Gennaio 2026 · IT