GUIDE D'INSTALLATION
16 étapes vers un(e) Pergola bioclimatique manuelle murale terminé(e).
Pergola bioclimatique murale en aluminium à manivelle manuelle — la sablière murale PN-WM-500 remplace le cadre arrière autoportant, deux poteaux frontaux uniquement. Trois dimensions partageant une procédure unique en 16 étapes.
-
01
Tracer la ligne de la sablière murale
Mark the wall ledger line — the entire roof reference for a wall-mount install.
STRUCTURE15 min -
02
Ancrer la sablière murale (PN-WM-500)
Anchor PN-WM-500 wall ledger — replaces the rear free-standing frame.
STRUCTURE25 min -
03
Poser les deux plaques de pied avant
Place the two front PN-FP-500 foot plates parallel to the wall ledger.
STRUCTURE18 min -
04
Lever les deux poteaux avant
Lift the two front PN-DZ-500 pillars onto their foot plate studs.
STRUCTURE22 min -
05
Installer la gouttière porteuse avant
Install the front PN-GU-500 carrier gutter — match height to wall ledger ±2 mm.
STRUCTURE18 min -
06
Installer les gouttières latérales (avant vers mur)
Install left and right side gutters — wall-side ends fix to PN-WM-500 ledger.
STRUCTURE22 min -
07
Sceller les joints d'angle
Apply neutral-cure silicone bead at all four upper corner joints.
STRUCTURE12 min -
08
Installer les rails de lames (PN-RA-500)
Slide PN-RA-500 blade rails into the frame channels — pre-set pivot positions.
LAMES18 min -
09
Préparer les lames
Prepare the louvre blades (PN-LM-500 opening + PN-LM-501 fixed reference).
LAMES18 min -
10
Installer la lame fixe (PN-LM-501)
Install the PN-LM-501 fixed lamella against the wall ledger — closed-position reference.
LAMES15 min -
11
Installer les lames mobiles (PN-LM-500)
Install the PN-LM-500 opening lamellas (back/wall side first) — equal pitch.
LAMES25 min -
12
Connecter la tringlerie manuelle
Connect the manual synchronization linkage — all opening blades move together.
LAMES18 min -
13
Installer la manivelle manuelle (PN-HD-500)
Install the PN-HD-500 manual handle — front-side rail, smooth crank cycle.
LAMES18 min -
14
Régler les fins de course et installer les caches
Set open / close end-stops and install front pillar caps + gutter closing profiles.
FINITION18 min -
15
Installer les évacuations et test final
Connect drainage outlets in front pillars and complete final functional test.
FINITION18 min -
16
Nettoyer et remettre au client
Clean, demonstrate manual operation to customer, hand over warranty card.
FINITION12 min
À propos de ce guide d'installation pergola bioclimatique manuelle murale
Luxa Sereno 500M Wall — Pergola bioclimatique manuelle murale · LuxaShade aluminium roof family. 16 steps · 2 installers · Edition 2026.1.
EN AW-6063 T6 alloy · QUALICOAT class 2 powder coating · EN 1991-1-4 wind-load rated · RTS-compatible motor wiring on motorised variants.
Pourquoi suivre la procédure officielle PONARC × LuxaShade
- EN 1991-1-4 · QUALICOAT class 2 · EN AW-6063 T6
- RTS-compatible motor wiring (motorised variants)
- Gutter slope 1.5% · drainage inside columns
- Edition 2026.1 · Janvier 2026 · FR