INSTALLATIONSGUIDE
24 steg till en färdig Väggmonterad motoriserad pergola.
Väggmonterad aluminiumpergola — väggbärande balk PN-WB-500 ersätter den bakre fristående ramen, endast två främre pelare. Sex omkretsstorlekar (3×3 → 4×6) från en gemensam 24-stegsprocedur.
-
01
Markera väggbalkens linje
Mark the wall carrier beam line — sets the entire roof reference.
STOMME15 min -
02
Förankra väggbalken PN-WB-500
Anchor PN-WB-500 wall carrier beam — replaces the rear free-standing frame.
STOMME25 min -
03
Förmontera de två främre hörnanslutningssatserna
Pre-build the two FRONT corner connection sets — wall side has no corners.
STOMME12 min -
04
Bygg främre U-ramen på marken
Build the front U-frame on the ground (two front pillars + front beam).
STOMME18 min -
05
Lyft främre U-ramen på ankarna
Lift the front U-frame onto the slab anchors — two installers per side.
STOMME25 min -
06
Montera vänster sidoprofil D-1 (front till väggbalk)
Install left side profile D-1 from front-left corner to wall beam.
STOMME18 min -
07
Montera höger sidoprofil D-2 (front till väggbalk)
Install right side profile D-2 from front-right corner to wall beam.
STOMME18 min -
08
Kontrollera ramens vinkelräthet och sätt dräneringsproppar
Verify diagonals (3×3: 386 · 3×4: 466 · 3×5: 554.5 · 4×4: 527.5 · 4×5: 602.4 · 4×6: 683.7 cm) and seat front drainage plugs.
STOMME15 min -
09
Montera F-rännor i utskjutningsriktning
Mount F gutters in projection direction — slope 1.5% toward front pillars.
STOMME18 min -
10
Montera E-rännor i breddriktning
Mount E gutters in width direction — wall-side E sits flush against PN-WB-500.
STOMME18 min -
11
Fixera översta rännor uppifrån
Fix all top gutters from above with torque-controlled drill.
STOMME15 min -
12
Täta gummiskarvar
Seal four rubber junctions with neutral-cure silicone (incl. wall-side).
STOMME12 min -
13
Förbered standardlameller
Pre-cut and prepare standard PN-LM-500 lamellas to width.
LAMELLER20 min -
14
Förbered motorlamellen
Prepare the dedicated PN-LM-501 motor blade — drive coupling on motor side.
LAMELLER15 min -
15
Montera motorn på D-1-profilen
Mount the PN-MT-500 motor on the D-1 profile — cable exits FRONT pillar.
LAMELLER25 min -
16
Montera motorlamellen
Install motor blade first — verifies free rotation before adding the rest.
LAMELLER20 min -
17
Justera motorarmen
Adjust motor arm so the motor blade closes flush with the frame.
LAMELLER18 min -
18
Montera resterande lameller
Insert remaining standard lamellas (back/wall side first) — verify rotation by hand.
LAMELLER30 min -
19
Montera rörelsearmar
Install PN-AR-500 movement arms linking all blades to the motor blade.
LAMELLER25 min -
20
Montera rörelsearm-kåpor
Cap with PN-CV-500 movement-arm cover profiles.
AVSLUTNING15 min -
21
Montera främre pelarkåpor
Mount the two front pillar covers (wall side has no covers).
AVSLUTNING12 min -
22
Montera främre avslutningsprofil
Install the front cover profile — wall side is concealed by trim.
AVSLUTNING12 min -
23
Montera främre hörnkåpor
Install the two front corner covers (front-left and front-right only).
AVSLUTNING12 min -
24
Dra motorkablar och färdigställ elektrisk koppling
Route motor cables through front pillar and complete electrical wiring (RTS-compatible).
AVSLUTNING30 min
Om denna väggmonterad motoriserad pergola-installationsguide
Luxa Aperio 500 Wall — Väggmonterad motoriserad pergola · LuxaShade aluminium roof family. 24 steps · 2 installers · Edition 2026.1.
EN AW-6063 T6 alloy · QUALICOAT class 2 powder coating · EN 1991-1-4 wind-load rated · RTS-compatible motor wiring on motorised variants.
Varför följa det officiella PONARC × LuxaShade-förfarandet
- EN 1991-1-4 · QUALICOAT class 2 · EN AW-6063 T6
- RTS-compatible motor wiring (motorised variants)
- Gutter slope 1.5% · drainage inside columns
- Edition 2026.1 · Januari 2026 · SV