РУКОВОДСТВО ПО МОНТАЖУ
26 шагов до готового Отдельностоящая моторизованная пергола.
Отдельностоящая алюминиевая пергола с моторизованной крышей-ламелями — шесть размеров периметра (3×3 → 4×6) по единой 26-шаговой процедуре.
-
01
Подготовить угловые соединительные комплекты
Pre-build the four corner connection sets — set projection vs width orientation now.
КАРКАС12 мин -
02
Собрать переднюю U-раму
Insert the front C-1 gutter into B-1/B-2 pillars to form the front U-frame on the ground.
КАРКАС18 мин -
03
Собрать заднюю U-раму
Repeat for the rear C-2 gutter into A-1/A-2 pillars — keep both U-frames square.
КАРКАС18 мин -
04
Поднять U-рамы
Lift both U-frames simultaneously — two installers per frame, mind the powder coating.
КАРКАС25 мин -
05
Установить левый боковой профиль D-1
Install the left D-1 side perimeter profile between the two U-frames.
КАРКАС18 мин -
06
Установить правый боковой профиль D-2
Install the right D-2 side perimeter profile — frame is now closed.
КАРКАС18 мин -
07
Проверить диагонали и дренажные пробки
Verify diagonals match the size table (3×3: 386 · 3×4: 466 · 3×5: 554.5 · 4×4: 527.5 · 4×5: 602.4 · 4×6: 683.7 cm) and seat drainage plugs.
КАРКАС15 мин -
08
Смонтировать F-водостоки по направлению проекции
Mount F gutters in the projection direction.
КАРКАС18 мин -
09
Смонтировать E-водостоки по направлению ширины
Mount E gutters in the width direction — perimeter complete.
КАРКАС18 мин -
10
Закрепить верхние водостоки сверху
Fix all top gutters from above with 3.9 mm screws.
КАРКАС15 мин -
11
Уплотнить резиновые соединения
Seal rubber junctions at all gutter intersections — neutral silicone bead.
КАРКАС12 мин -
12
Подготовить стандартные ламели
Pre-cut and prepare the standard PN-LM-500 lamellas to width.
ЛАМЕЛИ20 мин -
13
Подготовить моторную ламель
Prepare the dedicated PN-LM-501 motor blade — drive coupling on motor side.
ЛАМЕЛИ15 мин -
14
Смонтировать электропривод на профиле D-1
Mount the PN-MT-500 motor on the D-1 profile per code map orientation.
ЛАМЕЛИ25 мин -
15
Установить моторную ламель
Install the motor blade onto the rotation pin first — verifies free movement.
ЛАМЕЛИ20 мин -
16
Отрегулировать рычаг электропривода
Adjust the motor arm angle so the motor blade closes flush.
ЛАМЕЛИ18 мин -
17
Установить оставшиеся ламели
Insert the remaining standard lamellas one by one — verify rotation by hand.
ЛАМЕЛИ30 мин -
18
Смонтировать рычаги привода ламелей
Install the PN-AR-500 movement arms linking all blades to the motor blade.
ЛАМЕЛИ25 мин -
19
Установить крышки рычагов привода
Cap with the PN-CV-500 movement-arm cover profiles.
ЛАМЕЛИ15 мин -
20
Установить крышки стоек
Mount the PN-DZ-510 pillar covers (4 corners).
ОТДЕЛКА12 мин -
21
Установить задний закрывающий профиль
Install the PN-CV-501 rear cover profile.
ОТДЕЛКА12 мин -
22
Установить передний закрывающий профиль
Install the PN-CV-502 front cover profile.
ОТДЕЛКА12 мин -
23
Установить угловые крышки
Install the corner cover trims at the four upper corners.
ОТДЕЛКА15 мин -
24
Проложить кабели электропривода
Route the motor cables down through the designated pillar channel.
ОТДЕЛКА15 мин -
25
Установить светодиодную ленту и крышку из ПВХ
Install the LED strip into the gutter recess and snap on the PVC cover.
ОТДЕЛКА18 мин -
26
Завершить электромонтаж
Complete electrical wiring at the controller — verify motor direction and end-stops.
ОТДЕЛКА30 мин
Об этом руководстве по монтажу отдельностоящая моторизованная пергола
Luxa Aperio 500 — Отдельностоящая моторизованная пергола · LuxaShade aluminium roof family. 26 steps · 2 installers · Edition 2026.1.
EN AW-6063 T6 alloy · QUALICOAT class 2 powder coating · EN 1991-1-4 wind-load rated · RTS-compatible motor wiring on motorised variants.
Почему важно следовать официальной процедуре PONARC × LuxaShade
- EN 1991-1-4 · QUALICOAT class 2 · EN AW-6063 T6
- RTS-compatible motor wiring (motorised variants)
- Gutter slope 1.5% · drainage inside columns
- Edition 2026.1 · Январь 2026 · RU