GHID DE INSTALARE
24 pași până la un(o) Pergolă motorizată de perete finalizat(ă).
Pergolă de perete din aluminiu — grinda portantă de perete PN-WB-500 înlocuiește cadrul posterior independent, doar doi stâlpi frontali. Șase dimensiuni (3×3 → 4×6) dintr-o procedură unică în 24 de pași.
-
01
Trasați linia grinzii portante de perete
Mark the wall carrier beam line — sets the entire roof reference.
CADRU15 min -
02
Ancorați grinda portantă de perete (PN-WB-500)
Anchor PN-WB-500 wall carrier beam — replaces the rear free-standing frame.
CADRU25 min -
03
Pre-asamblați cele două seturi de conexiune de colț frontale
Pre-build the two FRONT corner connection sets — wall side has no corners.
CADRU12 min -
04
Construiți cadrul U frontal la sol
Build the front U-frame on the ground (two front pillars + front beam).
CADRU18 min -
05
Ridicați cadrul U frontal pe ancore
Lift the front U-frame onto the slab anchors — two installers per side.
CADRU25 min -
06
Instalați profilul lateral stâng D-1 (frontal spre grindă perete)
Install left side profile D-1 from front-left corner to wall beam.
CADRU18 min -
07
Instalați profilul lateral drept D-2 (frontal spre grindă perete)
Install right side profile D-2 from front-right corner to wall beam.
CADRU18 min -
08
Verificați perpendicularitatea cadrului și introduceți dopurile de drenaj
Verify diagonals (3×3: 386 · 3×4: 466 · 3×5: 554.5 · 4×4: 527.5 · 4×5: 602.4 · 4×6: 683.7 cm) and seat front drainage plugs.
CADRU15 min -
09
Instalați jgheaburile F pe direcția proiecției
Mount F gutters in projection direction — slope 1.5% toward front pillars.
CADRU18 min -
10
Instalați jgheaburile E pe direcția lățimii
Mount E gutters in width direction — wall-side E sits flush against PN-WB-500.
CADRU18 min -
11
Fixați jgheaburile superioare de sus
Fix all top gutters from above with torque-controlled drill.
CADRU15 min -
12
Etanșați îmbinările din cauciuc
Seal four rubber junctions with neutral-cure silicone (incl. wall-side).
CADRU12 min -
13
Pregătiți lamelele standard
Pre-cut and prepare standard PN-LM-500 lamellas to width.
LAMELE20 min -
14
Pregătiți lamela motoare
Prepare the dedicated PN-LM-501 motor blade — drive coupling on motor side.
LAMELE15 min -
15
Instalați motorul pe profilul D-1
Mount the PN-MT-500 motor on the D-1 profile — cable exits FRONT pillar.
LAMELE25 min -
16
Instalați lamela motoare
Install motor blade first — verifies free rotation before adding the rest.
LAMELE20 min -
17
Reglați brațul motor
Adjust motor arm so the motor blade closes flush with the frame.
LAMELE18 min -
18
Instalați lamelele rămase
Insert remaining standard lamellas (back/wall side first) — verify rotation by hand.
LAMELE30 min -
19
Instalați brațele de mișcare
Install PN-AR-500 movement arms linking all blades to the motor blade.
LAMELE25 min -
20
Instalați capacele brațelor de mișcare
Cap with PN-CV-500 movement-arm cover profiles.
FINISARE15 min -
21
Instalați capacele stâlpilor frontali
Mount the two front pillar covers (wall side has no covers).
FINISARE12 min -
22
Instalați profilul de închidere frontal
Install the front cover profile — wall side is concealed by trim.
FINISARE12 min -
23
Instalați capacele de colț frontale
Install the two front corner covers (front-left and front-right only).
FINISARE12 min -
24
Trasați cablurile motorului și finalizați cablajul electric
Route motor cables through front pillar and complete electrical wiring (RTS-compatible).
FINISARE30 min
Despre acest ghid de instalare pergolă motorizată de perete
Luxa Aperio 500 Wall — Pergolă motorizată de perete · LuxaShade aluminium roof family. 24 steps · 2 installers · Edition 2026.1.
EN AW-6063 T6 alloy · QUALICOAT class 2 powder coating · EN 1991-1-4 wind-load rated · RTS-compatible motor wiring on motorised variants.
De ce să urmați procedura oficială PONARC × LuxaShade
- EN 1991-1-4 · QUALICOAT class 2 · EN AW-6063 T6
- RTS-compatible motor wiring (motorised variants)
- Gutter slope 1.5% · drainage inside columns
- Edition 2026.1 · Ianuarie 2026 · RO