INSTALLATIEHANDLEIDING
24 stappen naar een voltooide Wandgemonteerde gemotoriseerde pergola.
Wandgemonteerde aluminium pergola — wand-draagbalk PN-WB-500 vervangt het achterste vrijstaande frame, slechts twee voorste pilaren. Zes omtreksmaten (3×3 → 4×6) uit één gedeelde 24-stappenprocedure.
-
01
Wand-draagbalklijn aftekenen
Mark the wall carrier beam line — sets the entire roof reference.
FRAME15 min -
02
Wand-draagbalk PN-WB-500 verankeren
Anchor PN-WB-500 wall carrier beam — replaces the rear free-standing frame.
FRAME25 min -
03
De twee voorste hoekverbindingssets voormonteren
Pre-build the two FRONT corner connection sets — wall side has no corners.
FRAME12 min -
04
Voorste U-frame op de grond opbouwen
Build the front U-frame on the ground (two front pillars + front beam).
FRAME18 min -
05
Voorste U-frame op de ankers tillen
Lift the front U-frame onto the slab anchors — two installers per side.
FRAME25 min -
06
Linker zijprofiel D-1 monteren (voor naar wandbalk)
Install left side profile D-1 from front-left corner to wall beam.
FRAME18 min -
07
Rechter zijprofiel D-2 monteren (voor naar wandbalk)
Install right side profile D-2 from front-right corner to wall beam.
FRAME18 min -
08
Frame haaks controleren en afwateringsstoppen plaatsen
Verify diagonals (3×3: 386 · 3×4: 466 · 3×5: 554.5 · 4×4: 527.5 · 4×5: 602.4 · 4×6: 683.7 cm) and seat front drainage plugs.
FRAME15 min -
09
F-goten in projectierichting monteren
Mount F gutters in projection direction — slope 1.5% toward front pillars.
FRAME18 min -
10
E-goten in breedterichting monteren
Mount E gutters in width direction — wall-side E sits flush against PN-WB-500.
FRAME18 min -
11
Bovenste goten van bovenaf vastzetten
Fix all top gutters from above with torque-controlled drill.
FRAME15 min -
12
Rubberen verbindingen afdichten
Seal four rubber junctions with neutral-cure silicone (incl. wall-side).
FRAME12 min -
13
Standaard lamellen voorbereiden
Pre-cut and prepare standard PN-LM-500 lamellas to width.
LAMELLEN20 min -
14
Motorlamel voorbereiden
Prepare the dedicated PN-LM-501 motor blade — drive coupling on motor side.
LAMELLEN15 min -
15
Motor op D-1-profiel monteren
Mount the PN-MT-500 motor on the D-1 profile — cable exits FRONT pillar.
LAMELLEN25 min -
16
Motorlamel monteren
Install motor blade first — verifies free rotation before adding the rest.
LAMELLEN20 min -
17
Motorarm afstellen
Adjust motor arm so the motor blade closes flush with the frame.
LAMELLEN18 min -
18
Resterende lamellen monteren
Insert remaining standard lamellas (back/wall side first) — verify rotation by hand.
LAMELLEN30 min -
19
Bewegingsarmen monteren
Install PN-AR-500 movement arms linking all blades to the motor blade.
LAMELLEN25 min -
20
Bewegingsarm-afdekkingen monteren
Cap with PN-CV-500 movement-arm cover profiles.
AFWERKING15 min -
21
Voorste pilaarafdekkingen monteren
Mount the two front pillar covers (wall side has no covers).
AFWERKING12 min -
22
Voorste afdekprofiel monteren
Install the front cover profile — wall side is concealed by trim.
AFWERKING12 min -
23
Voorste hoekafdekkingen monteren
Install the two front corner covers (front-left and front-right only).
AFWERKING12 min -
24
Motorkabels routen en elektrische bedrading voltooien
Route motor cables through front pillar and complete electrical wiring (RTS-compatible).
AFWERKING30 min
Over deze wandgemonteerde gemotoriseerde pergola-installatiehandleiding
Luxa Aperio 500 Wall — Wandgemonteerde gemotoriseerde pergola · LuxaShade aluminium roof family. 24 steps · 2 installers · Edition 2026.1.
EN AW-6063 T6 alloy · QUALICOAT class 2 powder coating · EN 1991-1-4 wind-load rated · RTS-compatible motor wiring on motorised variants.
Waarom de officiële PONARC × LuxaShade-procedure volgen
- EN 1991-1-4 · QUALICOAT class 2 · EN AW-6063 T6
- RTS-compatible motor wiring (motorised variants)
- Gutter slope 1.5% · drainage inside columns
- Edition 2026.1 · Januari 2026 · NL