MONTAGEANLEITUNG
24 Schritte zur fertigen Wandmontierte motorisierte Pergola.
Wandmontierte Aluminium-Pergola — Wandträger PN-WB-500 ersetzt den hinteren freistehenden Rahmen, nur zwei vordere Säulen. Sechs Perimetergrößen (3×3 → 4×6) aus einer gemeinsamen 24-Schritt-Prozedur.
-
01
Wandträger-Linie anzeichnen
Mark the wall carrier beam line — sets the entire roof reference.
RAHMEN15 Min. -
02
Wandträger PN-WB-500 verankern
Anchor PN-WB-500 wall carrier beam — replaces the rear free-standing frame.
RAHMEN25 Min. -
03
Die zwei vorderen Eckverbindungssätze vormontieren
Pre-build the two FRONT corner connection sets — wall side has no corners.
RAHMEN12 Min. -
04
Vorderen U-Rahmen am Boden bauen
Build the front U-frame on the ground (two front pillars + front beam).
RAHMEN18 Min. -
05
Vorderen U-Rahmen auf die Anker heben
Lift the front U-frame onto the slab anchors — two installers per side.
RAHMEN25 Min. -
06
Linkes Seitenprofil D-1 montieren (Front zu Wandträger)
Install left side profile D-1 from front-left corner to wall beam.
RAHMEN18 Min. -
07
Rechtes Seitenprofil D-2 montieren (Front zu Wandträger)
Install right side profile D-2 from front-right corner to wall beam.
RAHMEN18 Min. -
08
Rahmen-Rechtwinkligkeit prüfen und Entwässerungsstopfen setzen
Verify diagonals (3×3: 386 · 3×4: 466 · 3×5: 554.5 · 4×4: 527.5 · 4×5: 602.4 · 4×6: 683.7 cm) and seat front drainage plugs.
RAHMEN15 Min. -
09
F-Regenrinnen in Projektionsrichtung montieren
Mount F gutters in projection direction — slope 1.5% toward front pillars.
RAHMEN18 Min. -
10
E-Regenrinnen in Breitenrichtung montieren
Mount E gutters in width direction — wall-side E sits flush against PN-WB-500.
RAHMEN18 Min. -
11
Obere Regenrinnen von oben fixieren
Fix all top gutters from above with torque-controlled drill.
RAHMEN15 Min. -
12
Gummiverbindungen abdichten
Seal four rubber junctions with neutral-cure silicone (incl. wall-side).
RAHMEN12 Min. -
13
Standard-Lamellen vorbereiten
Pre-cut and prepare standard PN-LM-500 lamellas to width.
LAMELLEN20 Min. -
14
Motorlamelle vorbereiten
Prepare the dedicated PN-LM-501 motor blade — drive coupling on motor side.
LAMELLEN15 Min. -
15
Motor auf D-1-Profil montieren
Mount the PN-MT-500 motor on the D-1 profile — cable exits FRONT pillar.
LAMELLEN25 Min. -
16
Motorlamelle montieren
Install motor blade first — verifies free rotation before adding the rest.
LAMELLEN20 Min. -
17
Motorarm justieren
Adjust motor arm so the motor blade closes flush with the frame.
LAMELLEN18 Min. -
18
Restliche Lamellen montieren
Insert remaining standard lamellas (back/wall side first) — verify rotation by hand.
LAMELLEN30 Min. -
19
Bewegungsarme montieren
Install PN-AR-500 movement arms linking all blades to the motor blade.
LAMELLEN25 Min. -
20
Bewegungsarm-Abdeckungen montieren
Cap with PN-CV-500 movement-arm cover profiles.
ABSCHLUSS15 Min. -
21
Vordere Säulenabdeckungen montieren
Mount the two front pillar covers (wall side has no covers).
ABSCHLUSS12 Min. -
22
Vorderes Abdeckprofil montieren
Install the front cover profile — wall side is concealed by trim.
ABSCHLUSS12 Min. -
23
Vordere Eckabdeckungen montieren
Install the two front corner covers (front-left and front-right only).
ABSCHLUSS12 Min. -
24
Motorkabel verlegen und Elektroinstallation abschließen
Route motor cables through front pillar and complete electrical wiring (RTS-compatible).
ABSCHLUSS30 Min.
Über diese wandmontierte motorisierte pergola-Montageanleitung
Luxa Aperio 500 Wall — Wandmontierte motorisierte Pergola · LuxaShade aluminium roof family. 24 steps · 2 installers · Edition 2026.1.
EN AW-6063 T6 alloy · QUALICOAT class 2 powder coating · EN 1991-1-4 wind-load rated · RTS-compatible motor wiring on motorised variants.
Warum die offizielle PONARC × LuxaShade-Anleitung befolgen
- EN 1991-1-4 · QUALICOAT class 2 · EN AW-6063 T6
- RTS-compatible motor wiring (motorised variants)
- Gutter slope 1.5% · drainage inside columns
- Edition 2026.1 · Januar 2026 · DE